Examinando por Autor "Rodriguez-Santiago, Moisés"
Mostrando 1 - 2 de 2
- Resultados por página
- Opciones de ordenación
Ítem Experimental and Numerical Analysis for the Mechanical Characterization of PETG Polymers Manufactured with FDM Technology under Pure Uniaxial Compression Stress States for Architectural Applications(MDPI, 2020-09-25) Mercado-Colmenero, Jorge Manuel; La Rubia-García, María Dolores; Mata-García, Elena; Rodriguez-Santiago, Moisés; Martín-Doñate, CristinaThis paper presents the numerical and experimental analysis performed on the polymeric material Polyethylene Terephthalate Glycol (PETG) manufactured with Fused Deposition Modeling Technology (FDM) technology, aiming at obtaining its mechanical characterization under uniaxial compression loads. Firstly, with the objective of evaluating the printing direction that poses a greater mechanical strength, eighteen test specimens were manufactured and analyzed according to the requirements of the ISO-604 standards. After that, a second experimental test analyzed the mechanical behavior of an innovative structural design manufactured in Z and X–Y directions under uniaxial compression loads according to the requirements of the Spanish CTE standard. The experimental results point to a mechanical linear behavior of PETG in X, Y and Z manufacturing directions up to strain levels close to the yield strength point. SEM micrographs show different structural failures linked to the specimen manufacturing directions. Test specimens manufactured along X present a brittle fracture caused by a delamination process. On the contrary, test specimens manufactured along X and Y directions show permanent plastic deformations, great flexibility and less strength under compression loads. Two numerical analyses were performed on the structural part using Young’s compression modulus obtained from the experimental tests and the load specifications required for the Spanish CTE standards. The comparison between numerical and experimental results presents a percentage of relative error of 2.80% (Z-axis), 3.98% (X-axis) and 3.46% (Y-axis), which allows characterizing PETG plastic material manufactured with FDM as an isotropic material in the numerical simulation software without modifying the material modeling equations in the data software. The research presented here is of great help to researchers working with polymers and FDM technology for companies that might need to numerically simulate new designs with the PETG polymer and FDM technology.Ítem Using numerical-experimental analysis to evaluate rPET mechanical behavior under compressive stresses and MEX additive manufacturing for new sustainable designs(Emerald insight, 2023-07-02) Mercado-Colmenero, Jorge Manuel; La Rubia, M. Dolores; Mata-García, Elena; Rodriguez-Santiago, Moisés; Martin-Doñate, CristinaPurpose – Because of the anisotropy of the process and the variability in the quality of printed parts, finite element analysis is not directly applicable to recycled materials manufactured using fused filament fabrication. The purpose of this study is to investigate the numericalexperimental mechanical behavior modeling of the recycled polymer, that is, recyclable polyethylene terephthalate (rPET), manufactured by a deposition FFF process under compressive stresses for new sustainable designs. Design/methodology/approach – In all, 42 test specimens were manufactured and analyzed according to the ASTM D695-15 standards. Eight numerical analyzes were performed on a real design manufactured with rPET using Young’s compression modulus from the experimental tests. Finally, eight additional experimental tests under uniaxial compression loads were performed on the real sustainable design for validating its mechanical behavior versus computational numerical tests. Findings – As a result of the experimental tests, rPET behaves linearly until it reaches the elastic limit, along each manufacturing axis. The results of this study confirmed the design’s structural safety by the load scenario and operating boundary conditions. Experimental and numerical results show a difference of 0.001–0.024 mm, allowing for the rPET to be configured as isotropic in numerical simulation software without having to modify its material modeling equations. Practical implications – The results obtained are of great help to industry, designers and researchers because they validate the use of recycled rPET for the ecological production of real-sustainable products using MEX technology under compressive stress and its configuration for numerical simulations. Major design companies are now using recycled plastic materials in their high-end designs. Originality/value – Validation results have been presented on test specimens and real items, comparing experimental material configuration values with numerical results. Specifically, to the best of the authors’ knowledge, no industrial or scientific work has been conducted with rPET subjected to uniaxial compression loads for characterizing experimentally and numerically the material using these results for validating a real case of a sustainable industrial product.